全新宝来自动挡变速箱油更换方法，新宝来自动变速箱油怎么换？

新宝来自动变速箱油怎么换

1、先把车架起来，然后，找个大器皿垫在车底下，以备接废油用。

2、用合适的螺丝刀拆下变速箱里、外壳，这时会有一些变速箱油流出，注意躲避。几分钟之后，当部分油快流干之后，取下最后一个油槽，注意要用手小心托住，这里还有大量的废油。

3、当取下来的时候，会看到有不少污渍残留在油槽的底部。小心地卸下变速箱油过滤器，这时可以清晰地看到用于控制挡位切换的电磁阀。

4、摘下油底垫圈，去除周边的污渍，如果缝隙清洁不干净可以借助工具。由于时间长，油垫圈上的胶皮粘在机器边缘不易清理，需要小刮刀来清除，同时喷一些化油器清洁剂，会清洁的更彻底。

5、用棉丝将所有清洁过的变速箱油过滤装置擦干净，逐一安装即可。

【英文介绍/For English】：

1. Put the car up first, and then find a large utensil to put it under the car for the waste oil.

2. Use a suitable screwdriver to remove the inner and outer casing of the gearbox. At this time, some gearbox oil will flow out, so be careful to avoid it. After a few minutes, when some of the oil is almost dry, remove the last oil tank and be careful to hold it with your hands, there is still a lot of waste oil.

3. When you take it off, you will see a lot of stains remaining on the bottom of the oil tank. Carefully remove the transmission oil filter, the solenoid valve that controls the gear shifting can now be clearly seen.

4. Take off the oil bottom gasket and remove the surrounding stains. If the gap is not clean, you can use tools. Due to the long time, the rubber on the oil washer sticks to the edge of the machine and is not easy to clean. It needs a small scraper to remove it. At the same time, spray some carburetor cleaner to clean it more thoroughly.

5. Wipe all the cleaned transmission oil filter devices with cotton silk and install them one by one.

全新宝来自动挡变速箱油更换方法

宝来自动挡变速箱油更换方法如下：

1.先将车停在平坦的地面上，然后将手刹拉紧，松开变速杆上的齿轮。

2.找到变速箱下方的油盘和油塞，用扳手拧开油塞，将变速箱油放到油盘里。

3.用清洁剂和干净布将油盘和油塞上的油污清洗干净，并检查油盘和油塞是否有损坏或松动的情况。

4.将旧的变速箱油排干后，用油漏斗将新的变速箱油倒入变速箱，直到油面上涨到正确的位置。

5.然后将油塞重新拧回，紧固后按压几次制动器来排除气泡。

6.最后启动车辆，让车跑一段时间，以确保变速箱油已经充分的润滑全系统。同时检查变速器是否正常工作，并确认油面是否位于指示线之内。